Q1. Alternating Current has:
Candidate Answer - A changing polarity, an amplitude component and a frequency,
Result - Correct
Q2. The Electrical Pressure that moves charged particles in a circuit is measured in
Candidate Answer - Volts
Result - Correct
Q3. Electrical Resistance is a property a material possesses to __________ the flow of electricity
Candidate Answer - Restrict
Result - Correct
Q4. You have a 55w bulb running a conventional 12v system, what will the current flow be?
Candidate Answer - 4.58 Amps
Result - Correct
Q5. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q6. The sum of the individual voltage drops in a series circuit must be ______ the applied voltage
Candidate Answer - half of
Result - Incorrect
Q7. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Ohm's Law
Result - Incorrect
Q8. A resistor is defined as an electrical component designed to have a resistance against the flow of ___________
Candidate Answer - Electrons
Result - Correct
Q9. When circuit elements are connected so that two terminals are shared and voltage is common across the shared terminals this is called
Candidate Answer - Parallel
Result - Correct
Q10. An adjustable or variable resistor is known as a
Candidate Answer - Diode
Result - Incorrect
Q11. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Fuse
Result - Correct
Q12. A __________________ is a device placed in series with a power line which, when an excess amount of current is sensed, will open the power connection, thus protecting a circuit or system.
Candidate Answer - Diode
Result - Incorrect
Q13. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Additive
Result - Incorrect
Q14. A fuse connected in-line at the battery is there to protect
Candidate Answer - The wire and equipment connected
Result - Correct
Q15. When connecting a high current device, connect a fuse at the battery no more than 25 cm from the battery and make sure it is
Candidate Answer - After the bulkhead
Result - Incorrect
Q16. No current can flow in an
Candidate Answer - Open circuit
Result - Correct
Q17. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 86 must always be connected the Negative (-) terminal and 87 must always be connected to the Positive (+) terminal
Result - Incorrect
Q18. Where a relay has extra contacts labelled 30, 85, 86 ,87 and 87a the relay will be a
Candidate Answer - Single pole double throw
Result - Correct
Q19. The process of changing AC current to DC current is known as
Candidate Answer - Rectification
Result - Correct
Q20. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q21. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Secondary battery
Result - Correct
Q22. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q23. Using the wrong cable (too small) size for the type of application could cause the cable to
Candidate Answer - Overheat and melt
Result - Correct
Q24. A diode is used to:
Candidate Answer - As a suppressor
Result - Incorrect
Q25. When a diode conducts there will be a______ drop across it, and less voltage will be available for the equipment.
Candidate Answer - 0.7 volt
Result - Correct
Q26. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q27. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q28. What component are we describing in the article below ‘An accelerant is ignited which in turn ignites the gas generating material, causing an explosion’
Candidate Answer - Hydrogen Cell
Result - Incorrect
Q29. A good solder joint should be
Candidate Answer - Smooth, shiny and concave
Result - Correct
Q30. In case of any conflict when complying with installation instructions, which instruction take priority?
Candidate Answer - The wiring manufacturer
Result - Incorrect
Q31. What does EMC stand for?
Candidate Answer - Electro Magnetic Compatibility
Result - Correct
Q32. What type of antenna may not be suitable for vehicles with double-glazed screens, reflective coatings or other special glass
Candidate Answer - Glass mount
Result - Correct
Q33. How much impedance should an ideal antenna cable have?
Candidate Answer - 50 Ohms
Result - Correct
Q34. The power supply cable you install should be
Candidate Answer - Cut to the correct length and as short as possible
Result - Correct
Q35. Why must an installer abide by the EMC Directive
Candidate Answer - To comply with the law
Result - Correct
Q36. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - The antenna can be checked to see if the ground has a good connection
Result - Incorrect
Q37. A GPS antenna needs to be installed:
Candidate Answer - With a clear view of the sky
Result - Correct
Q38. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q39. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Fit seat covers and any other protective equipment
Result - Correct
Q40. You have a high current device to connect to the vehicle. You should take the power from:
Candidate Answer - The battery
Result - Correct
Q41. You have just drilled a hole in a metal panel in the vehicle. The next step is:
Candidate Answer - Install a grommet
Result - Incorrect
Q42. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q43. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q44. What must the business provide to the technician before any work is carried out on a vehicle?
Candidate Answer - A CE mark to prove the installers competence
Result - Incorrect
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct