Q1. Alternating Current has:
Candidate Answer - A changing polarity, an amplitude component and a frequency,
Result - Correct
Q2. Direct Current is a the flow of ___________, which travel in one direction only
Candidate Answer - Electrons
Result - Correct
Q3. The measurable relationship between current, voltage, resistance and power is described in
Candidate Answer - Ohm's Law
Result - Correct
Q4. The conversion of energy into work over a certain period of time is
Candidate Answer - Kinetic
Result - Incorrect
Q5. The conversion of electrical energy into another form of work is measured in
Candidate Answer - Watts
Result - Correct
Q6. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q7. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Kirchhoff law
Result - Correct
Q8. A resistor is defined as an electrical component designed to have a resistance against the flow of ___________
Candidate Answer - Neutrons
Result - Incorrect
Q9. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Diode
Result - Incorrect
Q10. A __________________ is a device placed in series with a power line which, when an excess amount of current is sensed, will open the power connection, thus protecting a circuit or system.
Candidate Answer - Circuit Breaker
Result - Correct
Q11. A bad connection or any point of resistance on a circuit will cause a
Candidate Answer - Voltage drop
Result - Correct
Q12. Where more than one ground path is created, and different paths create a voltage differential, this is known as a
Candidate Answer - Ground loop
Result - Correct
Q13. A fuse connected in-line at the battery is there to protect
Candidate Answer - The wire and equipment connected
Result - Correct
Q14. When connecting a high current device, connect a fuse at the battery no more than 25 cm from the battery and make sure it is
Candidate Answer - After the bulkhead
Result - Incorrect
Q15. No current can flow in an
Candidate Answer - Closed circuit
Result - Incorrect
Q16. An electromechanical device that uses a coil (electro) to move switch contacts (mechanical) is known as a
Candidate Answer - Relay
Result - Correct
Q17. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q18. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 86 must always be connected the Negative (-) terminal and 87 must always be connected to the Positive (+) terminal
Result - Incorrect
Q19. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q20. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Primary battery
Result - Incorrect
Q21. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Multicore cable
Result - Incorrect
Q22. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q23. A professional installation is not just about the quality of your work. It also includes
Candidate Answer - Your preparedness and professionalism
Result - Correct
Q24. When the amperage draw of a system exceeds 120% of the alternator’s maximum output, which components will sustain damage
Candidate Answer - The battery and alternator
Result - Correct
Q25. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q26. What component are we describing in the article below ‘An accelerant is ignited which in turn ignites the gas generating material, causing an explosion’
Candidate Answer - Airbag
Result - Correct
Q27. It is always advisable to run power and signal leads away from each other. This is to avoid
Candidate Answer - Interference
Result - Correct
Q28. A good solder joint should be
Candidate Answer - Smooth, shiny and concave
Result - Correct
Q29. In case of any conflict when complying with installation instructions, which instruction take priority?
Candidate Answer - The vehicle manufacturer
Result - Correct
Q30. What does EMC stand for?
Candidate Answer - Electro Magnetic Compatibility
Result - Correct
Q31. Where is the optimum position for an antenna to obtain the best signal
Candidate Answer -
Result - Incorrect
Q32. How much impedance should an ideal antenna cable have?
Candidate Answer - 30 Ohms
Result - Incorrect
Q33. If the antenna cable is too short for the installation, ideally you should
Candidate Answer - Replace the antenna cable with the correct length
Result - Correct
Q34. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - The antenna can be tested regardless of whether the radio terminal is live on the network
Result - Correct
Q35. A GPS antenna needs to be installed:
Candidate Answer - With a clear view of the sky
Result - Correct
Q36. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q37. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Take your tool box out of your vehicle
Result - Incorrect
Q38. A fuse is ideally installed as close to the power as possible
Candidate Answer - To ensure the cable and device are protected.
Result - Correct
Q39. You have a high current device to connect to the vehicle. You should take the power from:
Candidate Answer - The battery
Result - Correct
Q40. You have just drilled a hole in a metal panel in the vehicle. The next step is:
Candidate Answer - Debur the hole and carefully remove any swarf
Result - Correct
Q41. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q42. You have a device which has a fuse installed on the device itself. Is it correct to install a separate fuse on the cable?
Candidate Answer - Yes, to protect the cable
Result - Correct
Q43. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q44. What must the business provide to the technician before any work is carried out on a vehicle?
Candidate Answer - A CE mark to prove the installers competence
Result - Incorrect
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - IMI
Result - Incorrect