Q1. Direct Current is a the flow of ___________, which travel in one direction only
Candidate Answer - Electrons
Result - Correct
Q2. The measurable relationship between current, voltage, resistance and power is described in
Candidate Answer - Ohm's Law
Result - Correct
Q3. The Electrical Pressure that moves charged particles in a circuit is measured in
Candidate Answer - Volts
Result - Correct
Q4. Electrical Resistance is a property a material possesses to __________ the flow of electricity
Candidate Answer - Restrict
Result - Correct
Q5. The conversion of energy into work over a certain period of time is
Candidate Answer - Power
Result - Correct
Q6. The conversion of electrical energy into another form of work is measured in
Candidate Answer - Watts
Result - Correct
Q7. You have a 55w bulb running a conventional 12v system, what will the current flow be?
Candidate Answer - 4.58 Amps
Result - Correct
Q8. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q9. The sum of the individual voltage drops in a series circuit must be ______ the applied voltage
Candidate Answer - less than
Result - Incorrect
Q10. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Kirchhoff law
Result - Correct
Q11. A resistor is defined as an electrical component designed to have a resistance against the flow of ___________
Candidate Answer - Electrons
Result - Correct
Q12. When circuit elements are connected so that two terminals are shared and voltage is common across the shared terminals this is called
Candidate Answer - Parallel
Result - Correct
Q13. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Total
Result - Correct
Q14. When connecting a high current device, connect a fuse at the battery no more than 25 cm from the battery and make sure it is
Candidate Answer - Before the bulkhead
Result - Correct
Q15. An electromechanical device that uses a coil (electro) to move switch contacts (mechanical) is known as a
Candidate Answer - Relay
Result - Correct
Q16. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q17. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 85 must always be connected the Negative (-) terminal and 86 must always be connected to the Positive (+) terminal
Result - Correct
Q18. Where a relay has extra contacts labelled 30, 85, 86 ,87 and 87a the relay will be a
Candidate Answer - Double pole single throw
Result - Incorrect
Q19. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q20. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Secondary battery
Result - Correct
Q21. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q22. What is an electrical two- terminal device which allows current to pass through it in one direction only
Candidate Answer - Diode
Result - Correct
Q23. A diode is used to:
Candidate Answer - Protect existing factory wiring systems
Result - Correct
Q24. When a diode conducts there will be a______ drop across it, and less voltage will be available for the equipment.
Candidate Answer - 0.7 volt
Result - Correct
Q25. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q26. A professional installation is not just about the quality of your work. It also includes
Candidate Answer - Your preparedness and professionalism
Result - Correct
Q27. When the amperage draw of a system exceeds 120% of the alternator’s maximum output, which components will sustain damage
Candidate Answer - The battery and alternator
Result - Correct
Q28. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q29. It is always advisable to run power and signal leads away from each other. This is to avoid
Candidate Answer - Interference
Result - Correct
Q30. To avoid EMC issues it is advisable to use a product that has CE marking, what does CE stand for in English
Candidate Answer - European Conformity
Result - Correct
Q31. In case of any conflict when complying with installation instructions, which instruction take priority?
Candidate Answer - The vehicle manufacturer
Result - Correct
Q32. What type of antenna may not be suitable for vehicles with double-glazed screens, reflective coatings or other special glass
Candidate Answer - Glass mount
Result - Correct
Q33. How much impedance should an ideal antenna cable have?
Candidate Answer - 25 Kohm
Result - Incorrect
Q34. Why must an installer abide by the EMC Directive
Candidate Answer - To comply with the law
Result - Correct
Q35. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - The antenna can be tested regardless of whether the radio terminal is live on the network
Result - Correct
Q36. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q37. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Fit seat covers and any other protective equipment
Result - Correct
Q38. Is it acceptable to install a transceiver or any other device in the load storage area of a vehicle
Candidate Answer - Yes, if it does not obstruct access to other items, and is safe for the device.
Result - Correct
Q39. A fuse is ideally installed as close to the power as possible
Candidate Answer - To ensure the cable and device are protected.
Result - Correct
Q40. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q41. You have a device which has a fuse installed on the device itself. Is it correct to install a separate fuse on the cable?
Candidate Answer - Yes, to protect the cable
Result - Correct
Q42. Should all equipment power supplies, whether taken from the ignition or battery circuits, be fused?
Candidate Answer - Yes, all fuses must be protected by an adequate fuse of the correct rating
Result - Correct
Q43. Are you responsible for the installation of used equipment to be compliant with the latest relevant legislation
Candidate Answer - Yes, the installer is responsible
Result - Correct
Q44. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct