Q1. Alternating Current has:
Candidate Answer - A changing polarity, an amplitude component and a frequency,
Result - Correct
Q2. The Electrical Pressure that moves charged particles in a circuit is measured in
Candidate Answer - Volts
Result - Correct
Q3. The conversion of energy into work over a certain period of time is
Candidate Answer - Power
Result - Correct
Q4. You have a 55w bulb running a conventional 12v system, what will the current flow be?
Candidate Answer - 4.58 Amps
Result - Correct
Q5. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q6. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Ohm's Law
Result - Incorrect
Q7. An adjustable or variable resistor is known as a
Candidate Answer - Capacitor
Result - Incorrect
Q8. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Fuse
Result - Correct
Q9. A __________________ is a device placed in series with a power line which, when an excess amount of current is sensed, will open the power connection, thus protecting a circuit or system.
Candidate Answer - Circuit Breaker
Result - Correct
Q10. A bad connection or any point of resistance on a circuit will cause a
Candidate Answer - Voltage drop
Result - Correct
Q11. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Total
Result - Correct
Q12. Where more than one ground path is created, and different paths create a voltage differential, this is known as a
Candidate Answer - Ground loop
Result - Correct
Q13. A ground loop creates interference. How is it created?
Candidate Answer - By any non zero resistances between the wiring to ground and each piece of equipment
Result - Correct
Q14. An electromechanical device that uses a coil (electro) to move switch contacts (mechanical) is known as a
Candidate Answer - Relay
Result - Correct
Q15. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q16. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 86 must always be connected the Negative (-) terminal and 85 must always be connected to the Positive (+) terminal
Result - Incorrect
Q17. The process of changing AC current to DC current is known as
Candidate Answer - Rectification
Result - Correct
Q18. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q19. Primary batteries can
Candidate Answer - Recharged by passing a direct current in the opposite direction of discharge
Result - Incorrect
Q20. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Primary battery
Result - Incorrect
Q21. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q22. Using the wrong cable (too small) size for the type of application could cause the cable to
Candidate Answer - Overheat and melt
Result - Correct
Q23. What is an electrical two- terminal device which allows current to pass through it in one direction only
Candidate Answer - Diode
Result - Correct
Q24. A diode is used to:
Candidate Answer - To keep current constant
Result - Incorrect
Q25. A professional installation is not just about the quality of your work. It also includes
Candidate Answer - Your preparedness and professionalism
Result - Correct
Q26. When the amperage draw of a system exceeds 120% of the alternator’s maximum output, which components will sustain damage
Candidate Answer - The battery and alternator
Result - Correct
Q27. What component are we describing in the article below ‘An accelerant is ignited which in turn ignites the gas generating material, causing an explosion’
Candidate Answer - Petrol Engine
Result - Incorrect
Q28. It is always advisable to run power and signal leads away from each other. This is to avoid
Candidate Answer - Interference
Result - Correct
Q29. To avoid EMC issues it is advisable to use a product that has CE marking, what does CE stand for in English
Candidate Answer - European Conformity
Result - Correct
Q30. Where is the optimum position for an antenna to obtain the best signal
Candidate Answer - Behind the bumper
Result - Incorrect
Q31. How much impedance should an ideal antenna cable have?
Candidate Answer - 50 Ohms
Result - Correct
Q32. If the antenna cable is too short for the installation, ideally you should
Candidate Answer - Replace the antenna cable with the correct length
Result - Correct
Q33. The power supply cable you install should be
Candidate Answer - Cut to the correct length and as short as possible
Result - Correct
Q34. Why must an installer abide by the EMC Directive
Candidate Answer - To comply with the law
Result - Correct
Q35. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q36. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Fit seat covers and any other protective equipment
Result - Correct
Q37. Is it acceptable to install a transceiver or any other device in the load storage area of a vehicle
Candidate Answer - Yes, if it does not obstruct access to other items, and is safe for the device.
Result - Correct
Q38. A fuse is ideally installed as close to the power as possible
Candidate Answer - To ensure the cable and device are protected.
Result - Correct
Q39. You have just drilled a hole in a metal panel in the vehicle. The next step is:
Candidate Answer - Paint the edges with a rust inhibitor
Result - Incorrect
Q40. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q41. You have a device which has a fuse installed on the device itself. Is it correct to install a separate fuse on the cable?
Candidate Answer - Yes, to protect the cable
Result - Correct
Q42. Are you responsible for the installation of used equipment to be compliant with the latest relevant legislation
Candidate Answer - No, the manufacturer is responsible
Result - Incorrect
Q43. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q44. What must the business provide to the technician before any work is carried out on a vehicle?
Candidate Answer - A risk assessment document
Result - Correct
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct