Q1. The measurable relationship between current, voltage, resistance and power is described in
Candidate Answer - Ohm's Law
Result - Correct
Q2. The conversion of electrical energy into another form of work is measured in
Candidate Answer - Watts
Result - Correct
Q3. You have a 55w bulb running a conventional 12v system, what will the current flow be?
Candidate Answer - 4.58 Amps
Result - Correct
Q4. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q5. The sum of the individual voltage drops in a series circuit must be ______ the applied voltage
Candidate Answer - less than
Result - Incorrect
Q6. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Marconi's Law
Result - Incorrect
Q7. A resistor is defined as an electrical component designed to have a resistance against the flow of ___________
Candidate Answer - Electrons
Result - Correct
Q8. An adjustable or variable resistor is known as a
Candidate Answer - Potentiometer
Result - Correct
Q9. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Fuse
Result - Correct
Q10. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Total
Result - Correct
Q11. Where more than one ground path is created, and different paths create a voltage differential, this is known as a
Candidate Answer - Ground loop
Result - Correct
Q12. A fuse connected in-line at the battery is there to protect
Candidate Answer - The wire and equipment connected
Result - Correct
Q13. When connecting a high current device, connect a fuse at the battery no more than 25 cm from the battery and make sure it is
Candidate Answer - Before the bulkhead
Result - Correct
Q14. An electromechanical device that uses a coil (electro) to move switch contacts (mechanical) is known as a
Candidate Answer - Relay
Result - Correct
Q15. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q16. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 85 must always be connected the Negative (-) terminal and 86 must always be connected to the Positive (+) terminal
Result - Correct
Q17. Where a relay has extra contacts labelled 30, 85, 86 ,87 and 87a the relay will be a
Candidate Answer - Single pole double throw
Result - Correct
Q18. The process of changing AC current to DC current is known as
Candidate Answer - Refraction
Result - Incorrect
Q19. Primary batteries can
Candidate Answer - Deliver electrical energy but cannot be recharged
Result - Correct
Q20. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Secondary battery
Result - Correct
Q21. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q22. What is an electrical two- terminal device which allows current to pass through it in one direction only
Candidate Answer - Diode
Result - Correct
Q23. A diode is used to:
Candidate Answer - Protect existing factory wiring systems
Result - Correct
Q24. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q25. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q26. In case of any conflict when complying with installation instructions, which instruction take priority?
Candidate Answer - The vehicle manufacturer
Result - Correct
Q27. What does EMC stand for?
Candidate Answer - Electro Magnetic Compatibility
Result - Correct
Q28. Where is the optimum position for an antenna to obtain the best signal
Candidate Answer - Roof of the vehicle
Result - Correct
Q29. What type of antenna may not be suitable for vehicles with double-glazed screens, reflective coatings or other special glass
Candidate Answer - Glass mount
Result - Correct
Q30. If the antenna cable is too short for the installation, ideally you should
Candidate Answer - Replace the antenna cable with the correct length
Result - Correct
Q31. The power supply cable you install should be
Candidate Answer - Cut to the correct length and as short as possible
Result - Correct
Q32. Why must an installer abide by the EMC Directive
Candidate Answer - To comply with the law
Result - Correct
Q33. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - The antenna can be checked to see if the ground has a good connection
Result - Incorrect
Q34. A GPS antenna needs to be installed:
Candidate Answer - With a clear view of the sky
Result - Correct
Q35. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q36. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Fit seat covers and any other protective equipment
Result - Correct
Q37. Is it acceptable to install a transceiver or any other device in the load storage area of a vehicle
Candidate Answer - Yes, if it does not obstruct access to other items, and is safe for the device.
Result - Correct
Q38. You have a high current device to connect to the vehicle. You should take the power from:
Candidate Answer - The battery
Result - Correct
Q39. You have just drilled a hole in a metal panel in the vehicle. The next step is:
Candidate Answer - Debur the hole and carefully remove any swarf
Result - Correct
Q40. You have a device which has a fuse installed on the device itself. Is it correct to install a separate fuse on the cable?
Candidate Answer - Yes, to protect the cable
Result - Correct
Q41. Should all equipment power supplies, whether taken from the ignition or battery circuits, be fused?
Candidate Answer - Yes, all fuses must be protected by an adequate fuse of the correct rating
Result - Correct
Q42. Are you responsible for the installation of used equipment to be compliant with the latest relevant legislation
Candidate Answer - Yes, the installer is responsible
Result - Correct
Q43. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q44. What must the business provide to the technician before any work is carried out on a vehicle?
Candidate Answer - A risk assessment document
Result - Correct
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct