Q1. Alternating Current has:
Candidate Answer - A changing polarity, an amplitude component and a frequency,
Result - Correct
Q2. Direct Current is a the flow of ___________, which travel in one direction only
Candidate Answer - Electrons
Result - Correct
Q3. The Electrical Pressure that moves charged particles in a circuit is measured in
Candidate Answer - Volts
Result - Correct
Q4. Electrical Resistance is a property a material possesses to __________ the flow of electricity
Candidate Answer - Restrict
Result - Correct
Q5. The conversion of energy into work over a certain period of time is
Candidate Answer - Potential
Result - Incorrect
Q6. The conversion of electrical energy into another form of work is measured in
Candidate Answer - Watts
Result - Correct
Q7. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q8. The voltage applied to a DC Series Circuit that must equal the sum of the voltage drops with a circuit is known as
Candidate Answer - Kirchhoff law
Result - Correct
Q9. A resistor is defined as an electrical component designed to have a resistance against the flow of ___________
Candidate Answer - Electrons
Result - Correct
Q10. An adjustable or variable resistor is known as a
Candidate Answer - Potentiometer
Result - Correct
Q11. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Fuse
Result - Correct
Q12. A __________________ is a device placed in series with a power line which, when an excess amount of current is sensed, will open the power connection, thus protecting a circuit or system.
Candidate Answer - Circuit Breaker
Result - Correct
Q13. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Total
Result - Correct
Q14. Where more than one ground path is created, and different paths create a voltage differential, this is known as a
Candidate Answer - Ground loop
Result - Correct
Q15. A ground loop creates interference. How is it created?
Candidate Answer - By any non zero resistances between the wiring to ground and each piece of equipment
Result - Correct
Q16. A fuse connected in-line at the battery is there to protect
Candidate Answer - The battery
Result - Incorrect
Q17. When connecting a high current device, connect a fuse at the battery no more than 25 cm from the battery and make sure it is
Candidate Answer - Before the bulkhead
Result - Correct
Q18. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q19. Where a relay has extra contacts labelled 30, 85, 86 ,87 and 87a the relay will be a
Candidate Answer - Double pole double throw
Result - Incorrect
Q20. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q21. The main battery on a vehicle is normally a lead-acid compound and can be recharged. It is known as a
Candidate Answer - Secondary battery
Result - Correct
Q22. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q23. Using the wrong cable (too small) size for the type of application could cause the cable to
Candidate Answer - Overheat and melt
Result - Correct
Q24. What is an electrical two- terminal device which allows current to pass through it in one direction only
Candidate Answer - Diode
Result - Correct
Q25. When a diode conducts there will be a______ drop across it, and less voltage will be available for the equipment.
Candidate Answer - 0.7 volt
Result - Correct
Q26. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q27. A professional installation is not just about the quality of your work. It also includes
Candidate Answer - Your preparedness and professionalism
Result - Correct
Q28. When the amperage draw of a system exceeds 120% of the alternator’s maximum output, which components will sustain damage
Candidate Answer - The battery and alternator
Result - Correct
Q29. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q30. What component are we describing in the article below ‘An accelerant is ignited which in turn ignites the gas generating material, causing an explosion’
Candidate Answer - Airbag
Result - Correct
Q31. It is always advisable to run power and signal leads away from each other. This is to avoid
Candidate Answer - Interference
Result - Correct
Q32. A good solder joint should be
Candidate Answer - Smooth, shiny and concave
Result - Correct
Q33. Where is the optimum position for an antenna to obtain the best signal
Candidate Answer - Roof of the vehicle
Result - Correct
Q34. What type of antenna may not be suitable for vehicles with double-glazed screens, reflective coatings or other special glass
Candidate Answer - Glass mount
Result - Correct
Q35. If the antenna cable is too short for the installation, ideally you should
Candidate Answer - Replace the antenna cable with the correct length
Result - Correct
Q36. Why must an installer abide by the EMC Directive
Candidate Answer - To comply with the law
Result - Correct
Q37. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - The antenna can be tested regardless of whether the radio terminal is live on the network
Result - Correct
Q38. A risk assessment is a careful examination of aspects of work that could
Candidate Answer - Cause harm to people
Result - Correct
Q39. Is it acceptable to install a transceiver or any other device in the load storage area of a vehicle
Candidate Answer - Yes, if it does not obstruct access to other items, and is safe for the device.
Result - Correct
Q40. A fuse is ideally installed as close to the power as possible
Candidate Answer - To protect the car
Result - Incorrect
Q41. You have a high current device to connect to the vehicle. You should take the power from:
Candidate Answer - The battery
Result - Correct
Q42. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q43. Should all equipment power supplies, whether taken from the ignition or battery circuits, be fused?
Candidate Answer - Yes, all fuses must be protected by an adequate fuse of the correct rating
Result - Correct
Q44. If the initial test of a GPS antenna is not consistent with expectations you should firstly:
Candidate Answer - Test the unit with a test GPS antenna mounted temporarily on the roof
Result - Correct
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct