Q1. The measurable relationship between current, voltage, resistance and power is described in
Candidate Answer - Ohm's Law
Result - Correct
Q2. The Electrical Pressure that moves charged particles in a circuit is measured in
Candidate Answer - Volts
Result - Correct
Q3. Electrical Resistance is a property a material possesses to __________ the flow of electricity
Candidate Answer - Restrict
Result - Correct
Q4. The conversion of energy into work over a certain period of time is
Candidate Answer - Kinetic
Result - Incorrect
Q5. The conversion of electrical energy into another form of work is measured in
Candidate Answer - Watts
Result - Correct
Q6. You have a 55w bulb running a conventional 12v system, what will the current flow be?
Candidate Answer - 4.58 Amps
Result - Correct
Q7. What is the resistance of a bulb with a current flow of 5amps with a voltage of 24Volts
Candidate Answer - 4.8 Ohms
Result - Correct
Q8. The sum of the individual voltage drops in a series circuit must be ______ the applied voltage
Candidate Answer - equal to
Result - Correct
Q9. An adjustable or variable resistor is known as a
Candidate Answer - Potentiometer
Result - Correct
Q10. Which component listed contains a wire or strip of metal that is installed in series with a power line that is designed to melt if it receives an excessive amount of current, is called
Candidate Answer - Fuse
Result - Correct
Q11. Adding up resistances in a series circuit will give the ________________ resistance
Candidate Answer - Total
Result - Correct
Q12. Where more than one ground path is created, and different paths create a voltage differential, this is known as a
Candidate Answer - Ground loop
Result - Correct
Q13. A ground loop creates interference. How is it created?
Candidate Answer - By any non zero resistances between the wiring to ground and each piece of equipment
Result - Correct
Q14. A fuse connected in-line at the battery is there to protect
Candidate Answer - The equipment connected
Result - Incorrect
Q15. No current can flow in an
Candidate Answer - Open circuit
Result - Correct
Q16. What are the main elements of a relay
Candidate Answer - Coil, spring, contacts
Result - Correct
Q17. Whenever the relay has an INTERNAL SPIKE SUPPRESSION DIODE, to activate the relay
Candidate Answer - 85 must always be connected the Negative (-) terminal and 86 must always be connected to the Positive (+) terminal
Result - Correct
Q18. Where a relay has extra contacts labelled 30, 85, 86 ,87 and 87a the relay will be a
Candidate Answer - Double pole single throw
Result - Incorrect
Q19. The process of changing AC current to DC current is known as
Candidate Answer - Rectification
Result - Correct
Q20. A battery can also be referred to as a
Candidate Answer - Capacitor
Result - Correct
Q21. What type of cable should NOT be used in a vehicle environment
Candidate Answer - Solid cable
Result - Correct
Q22. Using the wrong cable (too small) size for the type of application could cause the cable to
Candidate Answer - Overheat and melt
Result - Correct
Q23. A diode is used to:
Candidate Answer - Protect existing factory wiring systems
Result - Correct
Q24. When a diode conducts there will be a______ drop across it, and less voltage will be available for the equipment.
Candidate Answer - 0.7 volt
Result - Correct
Q25. In order to avoid self destruction, what is normally connected to an LED in series to limit the current across it
Candidate Answer - Resistor
Result - Correct
Q26. A professional installation is not just about the quality of your work. It also includes
Candidate Answer - Your preparedness and professionalism
Result - Correct
Q27. When the amperage draw of a system exceeds 120% of the alternator’s maximum output, which components will sustain damage
Candidate Answer - The battery and alternator
Result - Correct
Q28. Can Bus wires are twisted to help reduce
Candidate Answer - Interference
Result - Correct
Q29. What component are we describing in the article below ‘An accelerant is ignited which in turn ignites the gas generating material, causing an explosion’
Candidate Answer - Petrol Engine
Result - Incorrect
Q30. To avoid EMC issues it is advisable to use a product that has CE marking, what does CE stand for in English
Candidate Answer - European Conformity
Result - Correct
Q31. What does EMC stand for?
Candidate Answer - Electro Magnetic Compatibility
Result - Correct
Q32. Where is the optimum position for an antenna to obtain the best signal
Candidate Answer - Roof of the vehicle
Result - Correct
Q33. If the antenna cable is too short for the installation, ideally you should
Candidate Answer - Replace the antenna cable with the correct length
Result - Correct
Q34. The power supply cable you install should be
Candidate Answer - Cut to the correct length and as short as possible
Result - Correct
Q35. The main benefit of using an antenna analyser on an airwave device is:
Candidate Answer - To check that the connections to the radio are acceptable
Result - Incorrect
Q36. A GPS antenna needs to be installed:
Candidate Answer - With a clear view of the sky
Result - Correct
Q37. At the preinstallation stage after you have checked the condition of the interior, to prevent any damage to the vehicle you should
Candidate Answer - Fit seat covers and any other protective equipment
Result - Correct
Q38. A fuse is ideally installed as close to the power as possible
Candidate Answer - To ensure the cable and device are protected.
Result - Correct
Q39. You have just drilled a hole in a metal panel in the vehicle. The next step is:
Candidate Answer - Debur the hole and carefully remove any swarf
Result - Correct
Q40. Where is the optimum position of a separate microphone
Candidate Answer - On or near to the front centre interior light cluster
Result - Correct
Q41. You have a device which has a fuse installed on the device itself. Is it correct to install a separate fuse on the cable?
Candidate Answer - No, the fuse installed on the device is adequate
Result - Incorrect
Q42. Should all equipment power supplies, whether taken from the ignition or battery circuits, be fused?
Candidate Answer - Yes, all fuses must be protected by an adequate fuse of the correct rating
Result - Correct
Q43. Are you responsible for the installation of used equipment to be compliant with the latest relevant legislation
Candidate Answer - Yes, the installer is responsible
Result - Correct
Q44. What must the business provide to the technician before any work is carried out on a vehicle?
Candidate Answer - A risk assessment document
Result - Correct
Q45. When installing equipment into police vehicles, guidance is available from FCS1362 and from the Code of Practice from which organisation?
Candidate Answer - NAPFM
Result - Correct